FLOYD F60 – Wood Chip Quality Reference Guide

FLOYD F60 — Wood Chip Quality Reference Guide

Biomass Fuel Specification · EN ISO 17225-4 · GLOCK Standard

Internal Technical Reference

The FLOYD F60 CHP system requires high-quality wood chips to operate reliably and efficiently. The gasifier is sensitive to fuel quality — sub-standard chips cause gasifier blockages, tar formation, reduced gas quality, and unplanned downtime.

This reference guide defines acceptable fuel parameters per EN ISO 17225-4 and provides real photo examples to help operators and suppliers identify compliant material at delivery.

Key consumption: 55 kg/h of dry biomass at full load (60 kW electric · 130 kW thermal).

✅ Acceptable Quality — Visual Examples
✓ These materials are suitable for the F60 system
Good wood chip sample 1
✓ ACCEPTABLE

Clean hardwood chips

Uniform chip size, clean flat cuts, no shredding or excessive fines. Moisture content within specification.

  • Length: 20–40 mm predominantly
  • Main fraction: >60% in 16-45mm range
  • Colour: light-medium brown (dry)
  • No visible dust layer
Good wood chip sample 2
✓ ACCEPTABLE

Mixed hardwood/softwood chips

Chipped from clean construction offcuts. Suitable piece size with minimal fines fraction.

  • Length: 16–45 mm range (main fraction)
  • Maximum length: <70 mm
  • No painted or treated material
  • Low ash content (clean wood only)
Good wood chip sample 3
✓ ACCEPTABLE

Forestry residue chips

High-quality forestry chips. Slightly coarser but within tolerance. Well-dried and consistent.

  • Length: 30–50 mm (within main fraction)
  • Some coarse fraction 45-65mm (≤8% allowed)
  • Fines: minimal (<2% small fraction)
  • Good feed characteristics
⛔ Non-Compliant Quality — Visual Examples
✗ Do not accept these materials
Bad wood chip sample 1 - excessive fines
✗ REJECT

Excessive fines content

High proportion of dust and particles under 8 mm. Causes bridging and poor gas flow through the gasifier bed.

  • Fines: visibly >5% small fraction (<8mm)
  • Dusty appearance on delivery
  • Risks: feed blockages, dust explosions
  • Will need screening — or reject
Bad wood chip sample 2 - shredded
✗ REJECT

Shredded wood (fibrous)

Material produced by shredders or grinders instead of chippers. Fibrous texture compacts in feed system and blocks screws.

  • Form: shredded/ground, not chipped
  • Texture: fibrous, compactable
  • Risks: major feed system blockages
  • Reject on delivery — do not use
Bad wood chip sample 3 - oversized
⚠ SCREEN

Oversized chips (length)

Chips exceed 70 mm maximum length specification. Will jam screw conveyor and disrupt gasifier loading.

  • Length: many pieces >70–100 mm
  • Exceeds maximum length limit
  • Risks: conveyor jams, uneven gasification
  • Require screening before use
📋 EN ISO 17225-4 Specification Summary
Parameter Target Value (F60) Tolerance / Action Thresholds Delivery Action Explanation
Moisture Content 5% ≤ m ≤ 13% >13%: dryer needed · >15%: reject ✓ OK 5-13% Higher moisture reduces gasification efficiency and gas quality.
Chip Length (Main Fraction) 16–45 mm (≥60% mass) 45–65mm coarse: ≤8% · >70mm: reject ⚠ Screen if mixed Main fraction must be 16-45mm. Coarse fraction 45-65mm allowed up to 8%.
Maximum Length (L) ≤ 70 mm >70mm: screen or reject ⚠ Screen oversized Oversized chips block screw conveyor (see bad-3 photo above).
Coarse Fraction (45-65mm) ≤ 8% >8%: may need screening ⚠ Check distribution Coarse fraction 45-65mm allowed up to 8% of mass per GLOCK standard.
Fines — large (8-16mm) ≤ 20% >20%: borderline, may need screening ⚠ Monitor closely Large fines (8mm ≤ max. 20% < 16mm) affect feed consistency.
Fines — small (<8mm) ≤ 2% 2–5%: borderline · >5%: reject ✗ Reject >5% Small fines (<8mm) cause bridging and reduced gas flow (see bad-1 photo).
Chip Form Chipped only Shredded material: reject ✗ Reject shredded Shredded wood compacts and blocks feed system (see bad-2 photo).
Wood Type Clean wood only Painted/treated/MDF: reject ✓ Clean wood OK Contaminated wood releases harmful gases during gasification.
Ash Content < 1% >1%: monitor closely ✓ Typically OK Pure wood chips are naturally low in ash. Quality A1-B2 per EN ISO 17225-4.
💰 Quality Non-Conformance Cost Impact

Compliant Chips

$0

No additional investment. System runs at full efficiency with 55 kg/h consumption at rated load.

Screening Unit Required

$25,000

One-time investment. Handles oversized chips and excessive fines. Recommended for inconsistent supply.

Biomass Dryer Required

$100,000

For moisture 13–15%. Uses 40 kW CHP heat, 3 kW electric, 3t/day output. Max 2 CHP units per dryer.

Unplanned Downtime

~8 hrs

Gasifier cleaning per blockage incident. Reject non-compliant deliveries to avoid this cost.

Required Additional Equipment

Select any additional equipment needed based on your fiber quality. Costs will be automatically added to the configurator.

✅ Delivery Acceptance Checklist

✓ Accept Delivery If:

  • ✓Chips are clean-cut and flat — not fibrous or shredded
  • ✓Colour is light to medium brown (dry)
  • ✓Length predominantly 16–45 mm (main fraction ≥60%)
  • ✓Maximum length ≤ 70 mm
  • ✓No visible dust clouds on delivery
  • ✓Moisture meter reads 5-13%
  • ✓No painted, treated, or MDF wood present
  • ✓EN ISO 17225-4 supplier certificate available

✗ Reject or Escalate If:

  • ✗Material is shredded / has fibrous texture (like bad-2)
  • ✗Chips obviously > 70 mm in length (like bad-3)
  • ✗Heavy dust / fines visible in load (like bad-1)
  • ✗Dark green-brown colour (high moisture)
  • ✗Moisture meter reads <5% or >15%
  • ✗Painted, lacquered, or MDF material visible
  • ✗Soil, stones, or other contamination present
  • ✗No quality documentation from supplier
ℹ Technical Notes

Fiber Consumption & Load Factor

The F60 consumes 55 kg/h of dry biomass at 100% load (60 kW electric · 130 kW thermal). At minimum load (75%), consumption drops to ~41 kg/h. Poor chip quality reduces gasifier stability and can cause load fluctuations even at correct feed rate.

Dryer Unit Integration (Moisture 13–15%)

The optional dryer uses 40 kW of waste heat from the CHP (no reduction to electrical output) plus 3 kW electric. It processes up to 3 tonnes/day and reduces moisture to 5-10% (within specification range). A maximum of 2 F60 units can share one dryer. Investment: approximately $100,000.

Storage Recommendations

Store chips under cover to prevent moisture re-absorption. Use first-in/first-out stock rotation. Keep pile height under 3 m with adequate air circulation to prevent self-heating. Avoid direct sun exposure on the pile surface.

Standard Reference

All specifications follow EN ISO 17225-4 (Solid biofuels — Fuel specifications and classes — Part 4: Graded wood chips) and the GLOCK internal quality standard. For certification questions, contact your FLOYD technical representative.

FLOYD BioEnergy · F60 CHP System · Wood Chip Quality Reference · EN ISO 17225-4 · GLOCK Standard

Internal technical document — for use by operators and biomass procurement teams